Cart

Quick Links

Electronic Boost Control (EBC) Solenoid Kit
Electronic Boost Control (EBC) Solenoid Kit
Electronic Boost Control (EBC) Solenoid Kit

Electronic Boost Control (EBC) Solenoid Kit

5 out of 5 based on 8 customer ratings
(8 customer reviews)

$62.99

-

Add a Weather Pack connector kit to help with installation

Weather Pack 2 Position, 20-18 Gauge (3) Pack

Description

Enhance your boost control with our high-performance electronic boost control solenoid, compatible with MS3Pro, MS3X, MSPNP, DIYPNP, and other DIY Style MegaSquirt EMS systems (with the appropriate mods). This solenoid adjusts boost pressure to your turbo wastegate, offering precise control and reliability.

Features:

  • Compatibility: Works with MS3Pro, MS3X, MSPNP, DIYPNP, and other electronic boost controllers
  • Frequency: Operates at 19.5-40 Hz
  • Pressure Range: Maximum pressure of 125 psi, suitable for high-pressure setups
  • Usage: ideal for use with Single Port or Dual Port Wastegates
  • Replacement: Direct wire-in replacement for the discontinued GM EBC Solenoid. Lower duty cycle may be needed; reduce by 30% when replacing a GM valve and adjust as necessary.
  • Connections: Includes 1/8″ barb fittings and mounting hardware. Ports are 1/8″ NPT pipe thread for alternative connections
  • Wiring: Connect one wire to a 12V source and the other to the ECU. The valve wiring is not polarized, so either wire can be used for 12V Power.

Specifications:

  • Maximum Pressure: 125 psi
  • Operating Frequency: 19.5-40 Hz
  • Material: Durable construction for performance applications
  • Temperature: Avoid mounting the valve in direct extreme heat; keep maximum valve temperatures under 122°F

Installation:

EBC Diagram

Note: Do not plug the disconnected port; it must be vented to the atmosphere.

Wiring

  • One wire connects to a 12V Power
  • Other wire connects to the ECU
  • Note: wiring is not polarized, so it does not matter which wire goes to 12V Power

Included in Box:

  • Electronic Boost Control Solenoid
  • 1/8″ Barb Fittings
  • Mounting Hardware

Customer reviews

Rated 5 out of 5 stars
8 reviews
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

8 reviews for Electronic Boost Control (EBC) Solenoid Kit

Only logged in customers who have purchased this product may write a review.

I see 3 ports, but you only include 2 fittings.  Why?

  • The 3rd port is the “bleed” port and is open to atmosphere.

I’d like to use different fittings for my lines.  What size are the ports?

  • The ports are threaded for 1/8″ NPT.

I sometimes hear the solenoid clicking.  Is this normal?

  • Yes.  The solenoid has a high speed valve inside that is rapidly pulsed by the ECU.  You may on occasion hear the valve being cycled.  This is perfectly normal.  It’s not all that loud  so it’s likely you’ll never hear it, particularly with the engine running. Most current firmware versions do not cycle the solenoid with the engine off.

Can this be used with a supercharger to control boost?

  • No. It is intended to regulate pressure to a turbo wastegate. Superchargers generally do not have any equivalent means of boost control.

Questions & Answers

    Will this work with MS II, PCB 3.0?
  1. 0 votes
    Q Will this work with MS II, PCB 3.0?
    Asked by Gabe Madigan
    A

    Yes, as long as you use our boost control mod kit.

  2. Will this control 2 wastegates, or do you need 1 for each gate?
  3. 0 votes
    Q Will this control 2 wastegates, or do you need 1 for each gate?
    Asked by Greg Beauford
    A

    Yes, you can run two wastegates on the same output pressure line.

    A

    Yes, you can run two wastegates on the same output pressure line. This assumes that you are using a conventional twin turbo setup and not a compound or sequential turbo setup where you are trying to intentionally run the turbos at separate pressures - if it's the latter, you can use the MS3's second boost control table and a second solenoid.

  4. Will this work with megasquirt gold box
  5. 0 votes
    Q Will this work with megasquirt gold box
    Asked by Parker Norton
    A

    The gold box is not our product and I do not have full specifications on it, but I do not believe this will be a problem.

  6. I have a mustang mspnp2 will this work ? Do i need to modify
  7. 0 votes
    Q I have a mustang mspnp2 will this work ? Do i need to modify
    Asked by Joe
    A

    Yes, you can wire this directly up to the options port on the MSPNP.

  8. I've got the MS2 DIYPNP for my Turbo miata. The instructions were a bit confusing on how to wire in a boost controller. My factory harness has been heavily modified so I have a lot of extra unused wires in it to solder the solenoid wiring to. I went ahead and wired from the Boost control IN and OUT to two different open locations on the accessory board. I was thinking hooking both up to the solenoid would work, but my understanding is I need a switched 12V & "one" of those to control it. I'm not sure if I needed to jump out to in then to the accessory board or use DB15? Thanks!
  9. 0 votes
    Q I've got the MS2 DIYPNP for my Turbo miata. The instructions were a bit confusing on how to wire ...... Read more
    Asked by Greg Hattrup
    A

    The boost "IN" needs to be connected to a 5 volt output, such as PA0, PT6, or PT7. The "Out" is usually easiest to run through the DB15, although you can run it through an unused wire in the OEM harness. The solenoid itself would be wired to the "Out" pin and switched 12 volts.

  10. I'd like to replace my fittings. Can you please tell me what size I need (thread/fitting)? Thanks
  11. 0 votes
    Q I'd like to replace my fittings. Can you please tell me what size I need (thread/fitting)? Thanks
    Asked by Juan Busto
    A

    1/8" NPT pipe thread with 1/8" hose barb.

  12. does the solenoid come with fittings? or will I need to buy them separately
  13. 0 votes
    Q does the solenoid come with fittings? or will I need to buy them separately
    Asked by Jak stoll
    A

    Yes, we include fittings for 1/8" vacuum hose.

  14. is this a 2 port or 3 port mac solenoid? can you show us how to do it via 3 port for external wastegate? thank you
  15. 0 votes
    Q is this a 2 port or 3 port mac solenoid? can you show us how to do it via 3 port for external was...... Read more
    Asked by Mauro
    A

    This is a 3 port solenoid - not a Mac but a different manufacturer. Is this the diagram you're looking for?

     

    Solenoid vacuum diagram

  16. will this work with my DIYPNP Nippon Denso 76 Pin Unassembled Kit? Thank you
  17. 0 votes
    Q will this work with my DIYPNP Nippon Denso 76 Pin Unassembled Kit? Thank you
    Asked by Vas
    A

    Yes. The DIYPNP kit has a boost control circuit as standard equipment, no mod kits required.

  18. Do I need any thing els that is not included with this product to use this with my MS-PNP 2.
  19. 0 votes
    Q Do I need any thing els that is not included with this product to use this with my MS-PNP 2.
    Asked by Liam
    A

    As your ECU already has a boost control output, the only things not included that you may need would be some extra wiring and vacuum line.

Only registered users are eligible to enter questions