Showing 65–80 of 147 results
-
MegaSquirt GPIO Black Anodized Case
$48.00GPIO board case. This one has an AMPSEAL cutout on one end, and the other end blank. You may drill a hole if using the stereo jack for serial communication, or use the AMPSEAL for that. Note that these cases are a bit of a tight fit - we recommend solderi...
Add to cart -
DB37 Solder Cup Connector for MS3X
$7.99To make sure you can't accidentally switch the upper and lower harnesses, the MS3X harness uses a male DB37 connector instead of a female one. We've packaged a DB37 male solder cup connector and a metalized plastic backshell for your MS3X builds. See t...
Add to cart -
Bulkhead Vacuum Fitting
$2.49Bulkhead fittings, just like those included in our V2.2 kits and MapDaddy. It's made from black nylon, fits 1/8" vacuum line on both sides, and measures about 1 1/4" long. Use to replace broken fittings, or if you're running your MAP sensor or boost gauge...
Add to cart -
Replacement DB37 Female PCB Mount Connector
$5.99Replacement DB37 female PCB mount connector, as used on Stimulator kits. Could also be used on boards that plug into a MegaSquirt such as the TBI or TPI adapter board.
Add to cart -
MS Relay and Power Board – Case Bottom and Endplates
$27.00Case Bottom with Flanged Endplates Machined for MegaSquirt Relay Board Case is brushed aluminum finish. Black anodize finish is no longer available.
Add to cart -
MegaSquirt GPIO – Heat Sink Only
$9.50Included is a Heat Sink Machined for MegaSquirt GPIO Board Part # GPIO-HS Similar to our V3.0 heat sink, but this one is made specifically for the GPIO board from 1/8" aluminum.
Add to cart -
Zeal Engineering Daughterboard with Dual VR Conditioners
$43.99The Zeal Engineering Daughterboard was designed and developed by Ken Culver, one of the authors of the MS2/Extra and MS3 firmware. We're proud to now offer this daughter card in kit form. It was originally developed for the FC RX-7, but we have found it...
Add to cart -
Coil Driver Kit
$10.99Note: This part supersedes the Bosch BIP373. OnSemi EcoSPARK IGBT, perfect for use as a high current ignition driver and can be used as Q16 in your v3.57 or v3.0 MegaSquirt build. This is the same high current ignition driver as used in many of our...
Add to cart -
Bosch BIP373 Coil Driver Mod Kit
$10.00Note: This has been replaced by our Coil Driver Kit. The power transistor that Bosch uses in their own ECUs is now available to you! This is a 'mod kit' for installing a BIP373 in a Megasquirt, or replacing an older or damaged VB921 with the much impr...
Read more -
PCB V3.57 and V3.0 HEI Input Mod Kit
$9.99This mod kit can be used with MS1 and MS2. It's intended for the V3.57 boards, but can be used with the V3.0 as well; you just have to remove the XG1-XG2 and the TachSelect-OptoIn jumpers and replace them with the included header pins. The kit includes on...
Add to cart -
DLP-TXRX Internal USB/Serial Adapter
$31.00DLP-TXRX Internal USB/Serial Adapter This adapter is perfect for converting your Megasquirt from the standard DB-9 serial connection to the USB connection common on newer laptops. The DLP-TXRX can be used on the following MegaSquirt products: MS1 ...
Add to cart -
USB Tuning Cable
$7.50USB A to Mini B cable. Use this with the following products: MS3Pro EVO MS3Pro Ultimate CAN-EGT MS1 or MS2 V2.2 or V3.0 modified with DLP-TXRX mod kit We include this cable with MS3Pro EVO & Ultimate. Does not fit MS3 V3.0 or V3.57.
Add to cart -
TO-220 Mica insulator kit
$5.00[3 Pack] Mica insulator / hardware kit for TO-220 components. Used for V3.0 / V3.57 Q9 and Q12, as well as for BIP373 coil drivers. Heat sink compound recommended. Includes 3 of each: mica insulators mounting screws nuts lockwasher i...
Add to cart -
LM1815 Chip
$4.00Adaptive VR conditioner chip used in several versions of VR conditioning circuits. This is just the chip on its own; if you are looking for a complete package to add extra VR conditioners and a bit more to your MegaSquirt, see the Zeal Engineering Daughte...
Add to cart -
JimStim CPU
$12.99Included is the JimStim CPU. A microcontroller loaded with the latest code, currently V2.0.4.
Add to cart -
Replacement DB9 Female PCB Mount Connector
$2.49Replacement DB9 female PCB mount connector, as used in all our Megasquirt kits.
Add to cart
