Showing 49–64 of 147 results
-
MegaSquirt JimStim Stimulator Power Supply
$17.5012v DC Power Supply Plugs directly into your MegaSquirt JimStim Stimulator! Power supply supports 120 to 240 volt AC power.
Add to cart -
GPIO Basic Kit – Silver Case
$249.99This is a starting point for your GPIO (General Purpose Input/ Output) project. Because of the number of ways the GPIO can be built, we've opted to offer it as a basic kit to which you can add application packages to customize it for the MegaShift code, E...
Add to cart -
PKIT – GPIO Board Partial Kit
$178.00This is a very basic and incomplete starting point for building a GPIO (General Purpose Input/ Output) kit. It includes the main board, all SMD components soldered on, AMPSeal connector, and all the AMPSEAL pins, each crimped to a short length of TXL wire...
Add to cart -
GPIO Application Kit – EGT Input
$35.99Single EGT input kit using AD595AQ amplifier chip. Intended for use on the GPIO board, but could be used anywhere you wish to take our EGT probes or other K-type thermocouples and convert their signal to a 0-5 volt output. This includes enough parts to po...
Add to cart -
GPIO Application Kit – MegaShift
$34.99Use this application package to set up your GPIO (General Purpose Input/ Output) board (GPIO-K) for MegaShift. Includes the 4L60E and 4L80E build guide items. We've also included some extra components in case you're looking to change some features or ...
Add to cart -
CPU – MegaSquirt-II Daughterboard
$136.99MegaSquirt-II Daughterboard For upgrading your Megasquirt-I ECU, or replacement of your damaged MegaSquirt-II daughterboard. MS2 daughter cards are for use only with genuine Bowling & Grippo MegaSquirt mainboard PCBs. This is the latest version o...
Add to cart -
PKIT – MegaSquirt-I PCBv3.0 Partial Kit
$132.00MegaSquirt-I PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-I CPU and MPX4250 MAP Sensor for building a MegaSquirt-I PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for complete MegaSquirt-...
Read more -
PKIT – MegaSquirt-I PCBv2.2 Partial Kit
$115.00MegaSquirt-I PCBv2.2 Partial Kit PCBv2.2, MegaSquirt-I CPU and MPX4250 MAP Sensor for building a MegaSquirt-I PCB 2.2 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE. Click HERE for complete MegaSquirt-I ...
Read more -
CPU – MegaSquirt-I CPU
$999.00MegaSquirt-I CPU; Motorola 68HC908 microprocessor loaded with standard B&G MegaSquirt-I firmware version 3.0. This part is discontinued - sorry, we've sold out the whole stock. For use with any MegaSquirt PCB version 1, 2.2, 3.0, 3.57...
Read more -
PCB – MegaSquirt Relay Board PCB Only
$30.00MegaSquirt Relay Board PCB PCB Only for building a MegaSquirt Relay and Power Board. Complete Bill of Materials (parts listing) and schematics can be found HERE. Click HERE for a fully assembled relay board.
Add to cart -
TransStim PCB
$30.00The TransStim simulates a 4L60E transmission, and several others. This is the bare PCB to make one TransStim. Use it to test your MegaShift or other transmission controller. The TranStim™ will help you to: Validate and troubleshoot a newly built...
Read more -
DB15 Solder Cup Connector
$3.00DB15 female solder cup connector, as included in our V3.57 setups, DIYPNP, and VVTuner. Use this if you're making a new harness and prefer a soldered connection. This is the connector only; the backshell is sold separately.
Add to cart -
Jumper 10-Pack
$7.4910-pack of wire jumpers in 5 colors. These fit 0.1" headers and are used on the JimStim to make connections for testing additional circuitry. There are several other uses for them too.
Add to cart -
DB15 Metalized Plastic Backshell
$3.00Metalized plastic backshell for the DB15 spare I/O connector, as used on our DIYPNP, VVTuner, and V3.57 boards.
Add to cart -
Y Vacuum Fitting
$2.001/8" vacuum Y-fitting, as included in the MSPNP and Mustang plug and play packages. This is made of clear polycarbonate. Maximum pressure 125 psi. This plastic is tough enough to take 275 degree F engine temps, and won't crack even if exposed to Siberian ...
Add to cart -
Replacement Relay Board Relay
$7.99Single replacement Tyco relay for the relay board. This is a pretty standard relay (Mini-ISO) and may fit many OEM fuse boxes as well. SPST contacts, rated for 12 volts and 30 amps. Does not have a mounting tab, so trying to use it with spade terminals is...
Add to cart
