Showing 33–48 of 147 results
-
Replacement 277-1249-ND 4 Position Screw Terminal
$4.99Replacement 4 position block for relay board injector power terminals.
Add to cart -
Variable Resistor P3C3103-ND – Stim Pot
$3.00Variable resistor P3C3103-ND, 10K This is the potentiometer (pot) used in the MSStim22 and JimStim kits, as well as the TransStim P1 and P2. If you need to replace a worn out one, get a new one here. Sold individually.
Add to cart -
MS Harness Extra Wire Kit
$8.99This 8' wire with pre-crimped terminal can be poked into our MegaSquirt DB37 harness if an extra wire is needed for additional I/O (MSHarness12, available separately). Made of the same TXL rated automotive grade wiring as the rest of our MegaSquirt wiri...
Add to cart -
40 Pin DIP Socket AE7240-ND
$3.99Replacement AE7240-ND 40 pin socket. Used for the main board processor socket, as well as extension spacers on the MS3 daughter boards.
Add to cart -
Replacement 2N3906FS-ND Transistor
$3.00PNP 200 mA transistor. As used in the MSStim V2.2 and later.
Add to cart -
Replacement D-Sub Thumb Screw
$3.00Replacement thumb screw, as used on our wiring harnesses. Sold individually.
Add to cart -
555 Timer IC – through hole
$3.00The classic 555 timer integrated circuit, in an 8 pin DIP package. This little chip has plenty of uses. In the MegaSquirt lineup, the older Stim boards used it to generate an RPM signal, and the DIYPNP uses it in its knock circuit. See the MS1/Extra manua...
Add to cart -
-
CP-102A-ND Power Jack Connector
$3.00Replacement CP-102A-ND power jack connector. 5.5 mm OD, 2.1 mm ID. Used on the Stimulator, JimStim, and DIYPNP to connect to a power supply.
Add to cart -
DIYPNP Replacement Coil Driver Heat Sink
$2.00TO-220 heat sink as used on coil drivers for the DIYPNP. V1.1 DIYPNPs also used these for the voltage regulator, boost control, and a few other functions.
Add to cart -
8 Case Screws
$2.00This is a packadge of 8 replacement case screws. As used on the regular MegaSquirt cases and VVTuner.
Add to cart -
497-2055-5-ND RS232 Transceiver
$3.00Replacement 497-2055-5-ND RS232 transciever, 16 pin DIP package. Used as U6 in V3.0 and V2.2 MegaSquirts. This is a drop-in replacement for the MAX232.
Add to cart -
MegaSquirt Boost Control Mod Kit
$9.99Give your Megasquirt the ability to drive a boost control solenoid double up it's duty as an electronic boost controller. Includes all parts required to build the MSnS-E boost control circuit on your V2.2, V3.0, or V3.57 PCB, including FET, resistors, hea...
Add to cart -
4N25 Optoisolator – V3.0 U3
$3.00Replacement 4N25 optoisolator. Used as U3 in the V3.0 kits and U4 in the V2.2.
Add to cart -
IXDI604PI FET Driver – V3.0 U4
$3.99IXDI604PI dual inverting MOSFET driver. Replaces the IXDI404PI in the original bill of materials. This is U4 in a V3.0 board, U7 in a V2.2.
Add to cart
