Showing 17–32 of 154 results
-
MicroSquirt Module Hardware Kit
$9.50All the hardware you need to attach your MicroSquirt Module to a PCB, all headers for the uS Module and the mainboard you would attach it too are included, along with standoffs and screws for security. (1) male and female 50 pin shrouded header (1) ...
Add to cart -
MicroSquirt Module V2.2
$284.00MicroSquirt Module is a credit card sized engine management board! This board packs all the features of the MicroSquirt into a 3.5" x 2.4" PCB, with all components installed. This tiny ECU opens up unprecedented possibilities - there's never been a standa...
Add to cart -
MegaSquirt Relay Board – Assembled Unit
$264.99MegaSquirt Relay Board - Assembled Unit - Part# MSRelay-C Though the Relay/Power Board is not required, it is a convenience and can reduce the chance of miswiring during the installation. The relay board provides a central place for all of the required...
Add to cart -
PKIT – MegaSquirt-II PCBv3.0 Partial Kit
$232.00MegaSquirt-II PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-II daughterboard and MPX4250 MAP Sensor for building a MegaSquirt-II PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for comp...
Add to cart -
PKIT – MegaSquirt-III PCBv3.0 Partial Kit
$326.25MegaSquirt-III PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-III daughterboard and MPX4250 MAP Sensor for building a MegaSquirt-III PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for c...
Add to cart -
MegaSquirt-III Daughterboard Kit
$230.00Upgrading your MS1 or MS2 to the latest MS3 has never been easier with this processor replacement! We've packaged the MS3 daughter board with 2 of the 40 pin sockets, so it will match up with our cases (required for upgrade) which have cutouts for the SD ...
Add to cart -
MegaSquirt-III MS3X Expansion Card & Connector Kit
$110.49Put this small circuit board in your MegaSquirt-III to unlock its full potential! This board installs in the MS3 case with no soldering; just connect it with the included ribbon cables. Install the MS3X board to add this whole list of inputs and outputs t...
Add to cart -
MegaSquirt Relay Cable
$109.99High Quality 4' Relay Board cable for connecting your MegaSquirt ECU to your Relay Board. Works with MS1, MS2, or MS3, all standard main boards (includes not just the IAC and ignition pins - it also has the spare pins on 3 through 6). It has a shielded...
Add to cart -
MegaSquirt Wiring Bundle – 8′ Long
$62.99MegaSquirt Wiring Bundle 8' TXL wire, color coded with labeling printed on the wire every 3 inches -- no paper tags here! IAC and Ignition wires are included for MS-I / MS-2 use (or MS-3 Primary Harness use) Shielded Ignition input wire Grea...
Add to cart -
JimStim v1.5 MegaSquirt Stimulator with Wheel Simulator – Unassembled
$80.99Use this board to test the MegaSquirt's inputs and outputs on the bench, before you install it on a car! The JimStim features a microcontroller which allows the simulation of up to 30 different toothed wheels, in addition to the standard distributor s...
Add to cart -
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
$119.99DIYAutoTune Part# JimStim-C JimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the ...
Add to cart -
JimStimX Kit – MS3X Stimulator Expansion Board – Unassembled
$51.99The regular JimStim can test the main board on your MS3. But what if you'd like to see the inputs and outputs on the MS3X expansion card in action, too? Now it's easy - just add a JimStimX! Use the three pull-off jumpers on the JimStim to connect the 5 vo...
Add to cart -
MegaSquirt MS3X Wiring Bundle – 23″
$29.99MegaSquirt MS3X Wiring Bundle - Length = 23" ~23" of TXL High temp automotive grade wire. Color coded wiring with labeling printed on the wire every 6 inches -- no paper tags here! Use with MS3X Expansion board or other sequential device J...
Add to cart -
MPX4250 2.5 Bar MAP Sensor
$33.00MPX4250AP MAP Sensor Standard 2.5 bar Map Sensor used in MegaSquirt PCB 2.2/3.0/3.57 ECUs. Good for 21-22psi of boost, or for NA usage in non-boosted applications.
Add to cart -
MapDaddy 4 Bar MAP Sensor with Barometric Correction
$99.99Who's Your MapDaddy? - MapDaddy 4 Bar MAP Sensor with Barometric Correction Ready to rock your ride handling up to 44psi of BOOST! New version has a 4 bar MAP sensor combined with a 1 bar barometric pressure sensor to improve barometric pressure re...
Add to cart -
MegaSquirt V3.0 Case
$46.00This is the enclosure as used with the MegaSquirt-III V3.0 ECU. It includes cutouts for the SD card, USB port, and MS3X expansion card. This is the case included with all of our current MS1, MS2, and MS3 V3.0 ECU kits. It is required if you are upgradin...
Add to cart
