Showing 17–32 of 89 results
-
IXDI604PI FET Driver – V3.0 U4
$3.99IXDI604PI dual inverting MOSFET driver. Replaces the IXDI404PI in the original bill of materials. This is U4 in a V3.0 board, U7 in a V2.2.
Add to cart -
DB15 Solder Cup Connector
$3.00DB15 female solder cup connector, as included in our V3.57 setups, DIYPNP, and VVTuner. Use this if you're making a new harness and prefer a soldered connection. This is the connector only; the backshell is sold separately.
Add to cart -
Jumper 10-Pack
$7.4910-pack of wire jumpers in 5 colors. These fit 0.1" headers and are used on the JimStim to make connections for testing additional circuitry. There are several other uses for them too.
Add to cart -
DB15 Metalized Plastic Backshell
$3.00Metalized plastic backshell for the DB15 spare I/O connector, as used on our DIYPNP, VVTuner, and V3.57 boards.
Add to cart -
Y Vacuum Fitting
$2.001/8" vacuum Y-fitting, as included in the MSPNP and Mustang plug and play packages. This is made of clear polycarbonate. Maximum pressure 125 psi. This plastic is tough enough to take 275 degree F engine temps, and won't crack even if exposed to Siberian ...
Add to cart -
Replacement Relay Board Relay
$7.99Single replacement Tyco relay for the relay board. This is a pretty standard relay (Mini-ISO) and may fit many OEM fuse boxes as well. SPST contacts, rated for 12 volts and 30 amps. Does not have a mounting tab, so trying to use it with spade terminals is...
Add to cart -
DB37 Solder Cup Connector for MS3X
$6.50To make sure you can't accidentally switch the upper and lower harnesses, the MS3X harness uses a male DB37 connector instead of a female one. We've packaged a DB37 male solder cup connector and a metalized plastic backshell for your MS3X builds. See t...
Add to cart -
Bulkhead Vacuum Fitting
$2.49Bulkhead fittings, just like those included in our V2.2 kits and MapDaddy. It's made from black nylon, fits 1/8" vacuum line on both sides, and measures about 1 1/4" long. Use to replace broken fittings, or if you're running your MAP sensor or boost gauge...
Add to cart -
Bulkhead Vacuum Fitting – 1/8″ to 1/8″
$2.50Bulkhead fittings, just like those used in the MSPNP Gen 2 and MS3Pro PNP line. It's made from black nylon, fits 1/8" vacuum line on the outside and 1/8" inside, and measures about 1 1/4" long. Use to replace broken fittings, or if you're running your MAP...
Add to cart -
Replacement DB37 Female PCB Mount Connector
$5.99Replacement DB37 female PCB mount connector, as used on Stimulator kits. Could also be used on boards that plug into a MegaSquirt such as the TBI or TPI adapter board.
Add to cart -
MegaSquirt GPIO – Heat Sink Only
$9.50Included is a Heat Sink Machined for MegaSquirt GPIO Board Part # GPIO-HS Similar to our V3.0 heat sink, but this one is made specifically for the GPIO board from 1/8" aluminum.
Add to cart -
TO-220 Mica insulator kit
$5.00[3 Pack] Mica insulator / hardware kit for TO-220 components. Used for V3.0 / V3.57 Q9 and Q12, as well as for BIP373 coil drivers. Heat sink compound recommended. Includes 3 of each: mica insulators mounting screws nuts lockwasher i...
Add to cart -
LM1815 Chip
$4.00Adaptive VR conditioner chip used in several versions of VR conditioning circuits. This is just the chip on its own; if you are looking for a complete package to add extra VR conditioners and a bit more to your MegaSquirt, see the Zeal Engineering Daughte...
Add to cart -
JimStim CPU
$12.99Included is the JimStim CPU. A microcontroller loaded with the latest code, currently V2.0.4.
Add to cart -
Replacement DB9 Female PCB Mount Connector
$2.49Replacement DB9 female PCB mount connector, as used in all our Megasquirt kits.
Add to cart -
Replacement DB37 Male PCB Mount Connector
$2.99Replacement DB37 male PCB mount connector, as used on all regular Megasquirts, the Relay Board, and EEC-IV adapter boards.
Add to cart
