Cart

Quick Links

MegaSquirt 2

MegaSquirt 2 (MS2) is the second generation, available pre-assembled or as a kit for self-assembly, targeting engines with semi-sequential or batch-fire fuelling and wasted spark ignition. The MegaSquirt 2 shares the same software as the MicroSquirt but most options will require hardware customization. The software is ready to support a wide variety of engines out of the box, with the ability to control anything with one to eight cylinders with batch fire fuel injection and up to four channels of logic ignition. Over 40 different ignition modes are supported, from mainstream applications like the GM LS1, Ford Zetec, Bosch Motronic, and Chrysler Gen III Hemis to unusual modes like Renix Jeeps and the Suzuki Swift GTI.

EPA, CARB & Emissions Disclaimer- All ECU's are for race purposes only. It's your responsibility to remain in compliance with all federal, state, provincial, or other laws that apply to you.

Showing 1–16 of 20 results

  • MegaSquirt V3.0 PCB Components Kit

    $142.99

    This MSx30-Guts kit includes all the capacitors, diodes, integrated circuits, resistors, transistors, ECU connectors, the tube of heatsink compound and a bit of jumper wire in a Megasquirt V3.0 kit. The kit does not include the V3.0 PCB, case, endplates, ...

    Add to cart
  • 8′ MegaSquirt Wiring Harness (MS1/MS2/MS3 Ready)

    5 out of 5
    $99.99

    MegaSquirt Wiring Harness - 8 Feet Long We've completely redesigned our wire harness to help you get your fuel injection installation right the first time with several new features to help make your installation as easy and reliable as possible: ...

    Add to cart
  • MS230-K Kit with MapDaddy4 Upgrade

    $424.99

    Note:   Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost!  MegaSquirt-II Engine Management System with 3.0 Main Board - UnAssembled Kit; Part # MS230-K_m4 Th...

    Add to cart
  • MegaSquirt-II Programmable EFI System PCB3.0 – Kit

    5 out of 5
    $324.99

    Note:   Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost!  MegaSquirt-II Engine Management System with 3.0 main board - Unassembled Kit; Part # MS230-K The MS23...

    Add to cart
  • MegaSquirt Relay Board – Assembled Unit

    5 out of 5
    $264.99

    MegaSquirt Relay Board - Assembled Unit - Part# MSRelay-C Though the Relay/Power Board is not required, it is a convenience and can reduce the chance of miswiring during the installation. The relay board provides a central place for all of the required...

    Add to cart
  • MegaSquirt Relay Cable

    5 out of 5
    $109.99

    High Quality 4' Relay Board cable for connecting your MegaSquirt ECU to your Relay Board. Works with MS1, MS2, or MS3, all standard main boards (includes not just the IAC and ignition pins - it also has the spare pins on 3 through 6). It has a shielded...

    Add to cart
  • MegaSquirt Wiring Bundle – 8′ Long

    4.2727272727273 out of 5
    $62.99

    MegaSquirt Wiring Bundle 8' TXL wire, color coded with labeling printed on the wire every 3 inches -- no paper tags here! IAC and Ignition wires are included for MS-I / MS-2 use (or MS-3 Primary Harness use) Shielded Ignition input wire Grea...

    Add to cart
  • JimStim v1.5 MegaSquirt Stimulator with Wheel Simulator – Unassembled

    4.8 out of 5
    $80.99

    Use this board to test the MegaSquirt's inputs and outputs on the bench, before you install it on a car! The JimStim features a microcontroller which allows the simulation of up to 30 different toothed wheels, in addition to the standard distributor s...

    Add to cart
  • JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled

    5 out of 5
    $119.99

    DIYAutoTune Part# JimStim-C JimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the ...

    Add to cart
  • DB15 Pigtail Harness

    5 out of 5
    $23.99

    DB15 pigtail harness. Used for optional outputs on the expansion connector on V3.57 boards and for the V1.2 version of the MSPNP Gen 2 (the version with the red main board).

    Add to cart
  • DIYPNP Upgrade: Sequential Injection Kit

    5 out of 5
    $43.99

    Add two extra injector drivers to your DIYPNP with this new module and the latest MS2/Extra code! We've partnered with JBPerf to develop this tiny module with two extra injector drivers. Allows for fully sequential injection on a 4 cylinder engine, semi-s...

    Add to cart
  • MegaSquirt JimStim Stimulator Power Supply

    5 out of 5
    $17.50

    12v DC Power Supply Plugs directly into your MegaSquirt JimStim Stimulator! Power supply supports 120 to 240 volt AC power.

    Add to cart
  • CPU – MegaSquirt-II Daughterboard

    4.5714285714286 out of 5
    $136.00

    MegaSquirt-II Daughterboard For upgrading your Megasquirt-I ECU, or replacement of your damaged MegaSquirt-II daughterboard.  MS2 daughter cards are for use only with genuine Bowling & Grippo MegaSquirt mainboard PCBs. This is the latest version o...

    Add to cart
  • Jumper 10-Pack

    5 out of 5
    $7.49

    10-pack of wire jumpers in 5 colors. These fit 0.1" headers and are used on the JimStim to make connections for testing additional circuitry.   There are several other uses for them too.

    Add to cart
  • DB15 Metalized Plastic Backshell

    $3.00

    Metalized plastic backshell for the DB15 spare I/O connector, as used on our DIYPNP, VVTuner, and V3.57 boards.

    Add to cart
  • Zeal Engineering Daughterboard with Dual VR Conditioners

    $43.99

    The Zeal Engineering Daughterboard was designed and developed by Ken Culver, one of the authors of the MS2/Extra and MS3 firmware.  We're proud to now offer this daughter card in kit form. It was originally developed for the FC RX-7, but we have found it...

    Add to cart