Showing 1–16 of 23 results
-
MegaSquirt V3.0 PCB Components Kit
$142.99This MSx30-Guts kit includes all the capacitors, diodes, integrated circuits, resistors, transistors, ECU connectors, the tube of heatsink compound and a bit of jumper wire in a Megasquirt V3.0 kit. The kit does not include the V3.0 PCB, case, endplates, ...
Add to cart -
8′ MegaSquirt Wiring Harness (MS1/MS2/MS3 Ready)
$99.99MegaSquirt Wiring Harness - 8 Feet Long We've completely redesigned our wire harness to help you get your fuel injection installation right the first time with several new features to help make your installation as easy and reliable as possible: ...
Add to cart -
MS230-K Kit with MapDaddy4 Upgrade
$424.99Note: Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost! MegaSquirt-II Engine Management System with 3.0 Main Board - UnAssembled Kit; Part # MS230-K_m4 Th...
Add to cart -
MegaSquirt-II Programmable EFI System PCB3.0 – Kit
$324.99Note: Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost! MegaSquirt-II Engine Management System with 3.0 main board - Unassembled Kit; Part # MS230-K The MS23...
Add to cart -
MegaSquirt Relay Board – Assembled Unit
$264.99MegaSquirt Relay Board - Assembled Unit - Part# MSRelay-C Though the Relay/Power Board is not required, it is a convenience and can reduce the chance of miswiring during the installation. The relay board provides a central place for all of the required...
Add to cart -
MegaSquirt Wiring Bundle – 8′ Long
$62.99MegaSquirt Wiring Bundle 8' TXL wire, color coded with labeling printed on the wire every 3 inches -- no paper tags here! IAC and Ignition wires are included for MS-1 / MS-2 use (or MS-3 Primary Harness use) Shielded Ignition input wire Gre...
Add to cart -
JimStim v1.5 MegaSquirt Stimulator with Wheel Simulator – Unassembled
$80.99Use this board to test the MegaSquirt's inputs and outputs on the bench, before you install it on a car! The JimStim features a microcontroller which allows the simulation of up to 30 different toothed wheels, in addition to the standard distributor s...
Add to cart -
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
$119.99DIYAutoTune Part# JimStim-C JimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the ...
Read more -
DB15 Pigtail Harness
$23.99DB15 pigtail harness. Used for optional outputs on the expansion connector on V3.57 boards and for the V1.2 version of the MSPNP Gen 2 (the version with the red main board).
Add to cart -
DIYPNP Upgrade: Sequential Injection Kit
$43.99Add two extra injector drivers to your DIYPNP with this new module and the latest MS2/Extra code! We've partnered with JBPerf to develop this tiny module with two extra injector drivers. Allows for fully sequential injection on a 4 cylinder engine, semi-s...
Add to cart -
MS Harness Extra Wire Kit
$8.99This 8' wire with pre-crimped terminal can be poked into our MegaSquirt DB37 harness if an extra wire is needed for additional I/O (MSHarness12, available separately). Made of the same TXL rated automotive grade wiring as the rest of our MegaSquirt wiri...
Add to cart -
MegaSquirt JimStim Stimulator Power Supply
$17.5012v DC Power Supply Plugs directly into your MegaSquirt JimStim Stimulator! Power supply supports 120 to 240 volt AC power.
Add to cart -
CPU – MegaSquirt-II Daughterboard
$136.99MegaSquirt-II Daughterboard For upgrading your Megasquirt-I ECU, or replacement of your damaged MegaSquirt-II daughterboard. MS2 daughter cards are for use only with genuine Bowling & Grippo MegaSquirt mainboard PCBs. This is the latest version o...
Add to cart