Search Results for: Mazda Miata MS3Pro PNP ECU/feed/rss2
How to Use a BMW Motronic 55 Pin Adapter Board
If you haven’t already, please read the ‘disclaimer’ at the top of the parent page here. Updated 2/5/2008 Warning: This document is a work in progress. It is not complete, and some of the directions are filler text from other products. Do not use this article until it is complete! What does this board do?…
Read MoreJamesl’s Original ‘MegaSquirting Your MR2’ Article
(Warning! This article, and the setup discussed, focuses on the 1987 Toyota MR2 with the stock 4age engine and stock VAST ignition system. I do NOT know if this setup will work with any other car or any other model year of the MR2 – it definitely won’t work with cars using Toyota’s ESA…
Read MoreHow to MegaSquirt Your 4AGE Powered MKI Toyota MR2 or AE86 Corolla
(or other Toyota VAST Ignition Vehicle) Want to make your install as easy as possible? Our MSPNP fully assembled, plug and play, ready to run unit that makes installing MegaSquirt a snap. Click here for MSPNP installation instructions and you can order them here. For those who’d rather set this up the DIY way, read on. Also– if…
Read MoreHow to MegaSquirt Your TPI or TBI Chevy Small-Block V8 or V6
Engines covered: Pre-Optispark small block Chevy V8s with TPI or TBI injection and HEI ignition with electronic spark timing (seven or eight pin HEI module) Much of this article will apply to other 1980s era GM cars including injected big blocks and even fire V6s. TPI and TBI The Tuned Port Injection and Throttle Body…
Read More
2010 American Road Race of Champions
November 5-7, 2010 – Road Atlanta in Braselton ,GA Travis Nordwald takes 1st place in the ITA class at the Enduro on Sunday. Running an MSPNP ECU Congrats to Travis Nordwald and team! Travis sent in some in-car video footage of the event (gets more exciting after the warmup lap, about 4:00 in) …
Read More
DIYAUTOTUNE QuickTip: Additional Temp or Pressure Sensors
DIYAUTOTUNE QuickTip: Discover the benefits of integrating additional temperature or pressure sensors into your engine management system. Learn how to wire and configure these sensors to gather valuable data for optimal performance.
Read More
Tuning the MAT / IAT Correction Table to eliminate Heat Soak
Have you ever been driving your car, maybe on a warm day, and all is going well. You park and shut ‘er down for a few minutes, come back to fire her up, and she runs completely different, or struggles to run at all for a few seconds? We can help! Here’s how to eliminate Heat Soak issues during hot restarts, we walk you through dialing this in on your MegaSquirt, MSPNP, or MS3Pro ECU!
Read More
Motorsports Magic: Celebrating Team MSR’s 2023 SCCA Nationals Achievements
Motorsports isn’t just about speed; it’s a test of character and determination. In 2023, Eric Anderson and the MSR team pushed the limits of both their car and themselves at the SCCA SOLO Nationals. From the high of championship victories to the lows of unexpected challenges, theirs is a story of unwavering passion, camaraderie, and the pursuit of perfection.
Read MoreThere are several ‘optional’ or ‘choice required’ steps during assembly of the PCBv3 MegaSquirt units, how are the DIYAutoTune ECU‘s configured?
MegaSquirt-I EMS’s are setup by default as a fuel only EFI controller running though they are running the current stable release of the MS1/Extra firmware. These are configured to be triggered from the (-) negative terminal of the coil by default. It is fairly easy to convert them to be triggered from a Hall/Optical/Points trigger…
Read More