Home

Performance Fuel Injection Systems – HP Books HP1557

SKU: book-hp1557

DIYAutoTune CEO Jerry Hoffmann & Lead Engineer Matt Cramer explain practically everything you need to know about EFI in their illustrated book, Performance Fuel Injection Systems. Hoffmann & Cramer cover what you need to know about EFI system selection, installation options and tuning, including: MUST HAVE tools for working with electronics How to build an…

-

MegaSquirt V3.57 Case

SKU: E-MS3357-Case

This is the enclosure as used with the MegaSquirt-III V3.57 ECU.   It includes cutouts for the SD card, USB port, and MS3X expansion card. This is the case included with all of our current MS1, MS2, and MS3 V3.57 assembled ECUs.  It is required if you are upgrading from an an MS1 or MS2 with…

-

DIYPNP Upgrade: BIP373 Ignition Module and Heat Sink Kit

SKU: DP_BIP373-K

Add a BIP373 Ignition Module with Heat Sink to your DIYPNP EMS to directly fire coils that do not have their own internal ignitor.  This will allow you to convert vehicles that came with a single coil ignition system and distributor over to modern day coil-per-plug or wasted spark ignition fired directly from the ECU! The DIYPNP…

-

Innovate LC-1 Serial Cable – 37460

SKU: INNVT-3746

The Innovate LC-1 Serial Cable is essential for tuning and customizing your Innovate wideband, boost controllers, some MegaSquirt ECU‘s. This high-quality cable facilitates direct communication between your Innovate device and a PC, enabling easy programming and firmware updates via the LogWorks software. With its robust construction and reliable data transfer, the MTS Program Cable ensures…

-

PCB V3.57 and V3.0 HEI Input Mod Kit

SKU: MK-HEI

This mod kit can be used with MS1 and MS2. It’s intended for the V3.57 boards, but can be used with the V3.0 as well; you just have to remove the XG1-XG2 and the TachSelect-OptoIn jumpers and replace them with the included header pins. The kit includes one normal green jumper, one red jumper with…

-

GM 3 Bar MAP Sensor 6″ Pigtail

SKU: GM3bar_piggy

The 6-Inch GM 3 Bar Pigtail designed to streamline the installation of GM 3-Bar MAP Sensors. This pigtail features three wires, each with specific color coding for easy connection and accurate pressure measurements in your engine management system. Features: Three-Wire Design: Connects to GM 3-Bar MAP Sensors with three wires Extended Length: 6 inches for…

-

MegaSquirt Boost Control Mod Kit

SKU: MK-Boost

Give your Megasquirt the ability to drive a boost control solenoid double up it’s duty as an electronic boost controller. Includes all parts required to build the MSnS-E boost control circuit on your V2.2, V3.0, or V3.57 PCB, including FET, resistors, heat sink compound, mica insulator, and mounting hardware. We’ve used it with MS1/Extra and…

-

MegaSquirt Pull-up Resistors Mod Kit

SKU: mk-pullup

Six 1k 1/4w resistors, and four 470ohm 1/4w resistors. Perfect for use as ‘pullup resistors’ for your MS ECU modding needs. These can be used for several of the mods described in some of our car-specific install articles listed on the site. NOTE: This kit is for PCBv3.0, v3.57 and PCB2.2 MegaSquirt ECUs

-

MapDaddy 4 Bar MAP Sensor with Barometric Correction

SKU: MapDaddy4

Who’s Your MapDaddy? – MapDaddy 4 Bar MAP Sensor with Barometric Correction   Ready to rock your ride handling up to 44psi of BOOST! New version has a 4 bar MAP sensor combined with a 1 bar barometric pressure sensor to improve barometric pressure resolution. The ‘MapDaddy’ 4-bar Manifold Absolute Pressure (MAP) Sensor upgrade for the…

-