Showing 289–304 of 419 results
-
Y Vacuum Fitting
$2.001/8" vacuum Y-fitting, as included in the MSPNP and Mustang plug and play packages. This is made of clear polycarbonate. Maximum pressure 125 psi. This plastic is tough enough to take 275 degree F engine temps, and won't crack even if exposed to Siberian ...
Add to cart -
Weather Pack 16-14 Gauge Terminal Pack – 30 Terminal Sets
$13.49Run out of terminals for your Weather Pack kits (or bought a kit elsewhere that didn't have enough)? We have the pins and seals on their own, without any housings or other parts. This package contains 30 pairs of male and female Weather Pack terminals, pl...
Add to cart -
Weather Pack 20-18 Gauge Terminal Pack – 30 Terminal Sets
$16.00Run out of terminals for your Weather Pack kits (or bought a kit elsewhere that didn't have enough)? We have the pins and seals on their own, without any housings or other parts. This package contains 30 pairs of male and female Weather Pack terminals, pl...
Add to cart -
Weather Pack 3 Position, 16-14 Gauge (3) Pack
$8.49(3) 3 position weather pack sets including: (3) male and female connectors, (10) male and female 16-14 gauge pins, and (20) 16-14 gauge seals
Add to cart -
Weather Pack 3 Position, 20-18 Gauge (3) Pack
$8.49(3) 3 position weather pack sets including: (3) male and female connectors, (10) male and female 20-18 gauge pins, and (20) 20-18 gauge seals
Add to cart -
Replacement Relay Board Relay
$7.99Single replacement Tyco relay for the relay board. This is a pretty standard relay (Mini-ISO) and may fit many OEM fuse boxes as well. SPST contacts, rated for 12 volts and 30 amps. Does not have a mounting tab, so trying to use it with spade terminals is...
Add to cart -
MegaSquirt GPIO Black Anodized Case
$48.00GPIO board case. This one has an AMPSEAL cutout on one end, and the other end blank. You may drill a hole if using the stereo jack for serial communication, or use the AMPSEAL for that. Note that these cases are a bit of a tight fit - we recommend solderi...
Add to cart -
DB37 Solder Cup Connector for MS3X
$6.50To make sure you can't accidentally switch the upper and lower harnesses, the MS3X harness uses a male DB37 connector instead of a female one. We've packaged a DB37 male solder cup connector and a metalized plastic backshell for your MS3X builds. See t...
Add to cart -
Crimp Connector for IGN-1 or IGN-1CD
$7.99Metri-Pack crimp connector for wiring up IGN-1 or IGN-1CD coils. Like all of our 'ready to crimp' connectors- we include an extra terminal/pin, just in case you goof one up.
Add to cart -
Crimp Connector for IGN-4
$13.99Crimp connector and pins for IGN-4 coil. This is a standard "junior timer" sort of connector that has other uses such as Bosch crankshaft position sensors and throttle position sensors. Like all of our 'ready to crimp' connectors, we include an extra t...
Add to cart -
Crimp Connector for IGN-6
$5.99Included is a Weather Pack type connector for IGN-6 coils. The pins and seals are sized for 14 to 16 gauge wire. Like our other DIYAutoTune Weather Packs, we include an extra pin, just in case.
Add to cart -
Bulkhead Vacuum Fitting
$2.49Bulkhead fittings, just like those included in our V2.2 kits and MapDaddy. It's made from black nylon, fits 1/8" vacuum line on both sides, and measures about 1 1/4" long. Use to replace broken fittings, or if you're running your MAP sensor or boost gauge...
Add to cart -
Bulkhead Vacuum Fitting – 1/8″ to 1/8″
$2.50Bulkhead fittings, just like those used in the MSPNP Gen 2 and MS3Pro PNP line. It's made from black nylon, fits 1/8" vacuum line on the outside and 1/8" inside, and measures about 1 1/4" long. Use to replace broken fittings, or if you're running your MAP...
Add to cart -
Replacement DB37 Female PCB Mount Connector
$5.99Replacement DB37 female PCB mount connector, as used on Stimulator kits. Could also be used on boards that plug into a MegaSquirt such as the TBI or TPI adapter board.
Add to cart -
MS Relay and Power Board – Case Bottom and Endplates
$27.00Case Bottom with Flanged Endplates Machined for MegaSquirt Relay Board Case is brushed aluminum finish. Black anodize finish is no longer available.
Add to cart -
MegaSquirt GPIO – Heat Sink Only
$9.50Included is a Heat Sink Machined for MegaSquirt GPIO Board Part # GPIO-HS Similar to our V3.0 heat sink, but this one is made specifically for the GPIO board from 1/8" aluminum.
Add to cart