Search Results for: Crankshaft Position Sensor/feed/rss2/
DIYAutoTune Hall Effect Sensors
DIYAutoTune.com has sold several Hall effect sensors. Select your sensor from the list below to see the specifications for your sensor. Tabbed Mount Sensor New (Red Body) Threaded Sensor Old (Silver Body) Threaded Sensor Tabbed Mount Sensor Runs off 5 to 24 volts, and gives a nice square wave so there’s no variable voltage issues.…
Read MorePressure Sensor Diagram
This article features detailed wiring diagrams for pressure sensors, covering everything from MAP sensors to fuel and oil pressure sensors. These diagrams are designed to help you connect your sensors accurately, ensuring precise pressure readings and optimal performance. Whether you’re setting up a single sensor or multiple inputs, use these guides to streamline your installation…
Read MoreDIYPNP Documentation for 1995-1997 Toyota Tacoma / 4Runner
1995-1997 Toyota Tacoma / 4Runner USDM 3.4L 5VZFE V6 MT Test Vehicle Details: The vehicle used for drawing up these application docs was a USDM 1997 Toyota Tacoma 3.4L V6 with a 4WD manual transmission transplanted into a 1983 Toyota pickup body. All factory electronics/ignition system components are in place on the 83 body…
Read MoreDIYPNP Documentation for 1994-1995 Mazda Miata
1994-1995 Mazda Miata USDM 1.8L BP MT Test Vehicle Details: The vehicle used for drawing up these application docs was a USDM 1995 Mazda Miata 1.8L with a manual transmission. All factory electronics/ignition system components are in place and the factory wiring harness is in perfect condition. Other notes: MAF in place What to buy:…
Read MoreIgnition Control – DIYPNP v1.1
Ignition control is one of the more involved parts of the DIYPNP installation to set up, and may take a bit of trial and error if you do not have an application guide to cover what mods you need. This page will explain the ignition control, both the inputs and the outputs. We’ve made the…
Read MoreMain Board Assembly
First, you will want to decide which components you will be using, as not all installations need all components. Here is a list of what parts go with what circuit. Note that U3 is used for multiple circuits, and must be installed for any of the circuits to work. There are a couple parts that…
Read More
Using the Tooth Logger and Composite Logger
The tooth logger and composite logger TunerStudio’s tooth logger and composite logger are powerful tools for troubleshooting problems with the MegaSquirt’s RPM input. These are both under the Diagnostic and High Speed Loggers menu. The tooth log records the time between individual pulses from the crankshaft position sensor. The composite log works similarly to a…
Read MoreDIYPNP Documentation for 1988 – 1993 Ford Mustang 5.0L
1988 – 1993 Ford Mustang 5.0L V8 Test Vehicle Details: The vehicle used for drawing up these application docs was a USDM 1993 Ford Mustang 5.0L with a manual transmission. All factory electronics/ignition system components are in place and the factory wiring harness is in perfect condition. Other notes: MAF in place GT40P heads installed…
Read MoreInstalling a DIYAutoTune.com Crank Trigger
This article covers how to install the DIYAutoTune.com trigger wheels. You can use a variety of sensors with these; we’ve tested them with both Ford and GM VR sensor pickups. We recommend mounting the trigger wheel in the same orientation that Ford used on their EDIS installations when using these trigger wheels on a 4,…
Read More
Weather Pack Bulkhead Connector Kit
SKU: WP22M-K
$32.00
Use this giant 22 Position Weather Pack connector to run wires through a firewall or as a quick disconnect for your engine harness, or other components that need a lot of wires. Includes: (1) 22 position male and female connector (13) 20-18 gauge male and female pins (13) 16-14 gauge male and female pins (4)…
View Details-
Add to cart