Showing 1–16 of 18 results
-
MegaSquirt-3 PCB3.0 Kit with MapDaddy4 Upgrade
$539.00Important Note: Due to supply chain challenges and the lack of ability to have parts anodized at this time, we are transitioning to brushed silver enclosures. We appreciate your understanding. MegaSquirt-III Engine Management System w/PCB3.0 - Un...
Add to cart -
MegaSquirt-3 with PCB V3.0 Kit
$449.99Included is a MegaSquirt-III Engine Management System w/PCB3.0 - Unassembled Kit Part # MS330-K This MS330-K kit includes everything you will need to build your MegaSquirt-3. The genuine B&G partial kit with V3.0 PCB, everything in the standard Bil...
Add to cart -
MegaSquirt 3 EMS System V3.57
$689.99Important Note: Due to supply chain challenges and the lack of ability to have parts anodized at this time, we are transitioning to brushed silver enclosures. We appreciate your understanding. MegaSquirt 3 Engine Management System w/PCB3.57 - The...
Add to cart -
MegaSquirt-I Programmable EFI System PCB2.2 – Kit
$197.00*This product or components that make up this product have reached End of Life. The ECU is now discontinued - this page is for reference only. MegaSquirt-I with V2.2 Main Board MegaSquirt programmable EFI Engine Management System from Bowling and ...
Read more -
MS230-K Kit with MapDaddy4 Upgrade
$424.99Note: Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost! MegaSquirt-II Engine Management System with 3.0 Main Board - UnAssembled Kit; Part # MS230-K_m4 Th...
Add to cart -
MegaSquirt-II Programmable EFI System PCB3.0 – Kit
$324.99Note: Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost! MegaSquirt-II Engine Management System with 3.0 main board - Unassembled Kit; Part # MS230-K The MS23...
Add to cart -
MicroSquirt Module V2.2
$284.00MicroSquirt Module is a credit card sized engine management board! This board packs all the features of the MicroSquirt into a 3.5" x 2.4" PCB, with all components installed. This tiny ECU opens up unprecedented possibilities - there's never been a standa...
Add to cart -
PKIT – MegaSquirt-II PCBv3.0 Partial Kit
$232.00MegaSquirt-II PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-II daughterboard and MPX4250 MAP Sensor for building a MegaSquirt-II PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for comp...
Add to cart -
PKIT – MegaSquirt-III PCBv3.0 Partial Kit
$326.25MegaSquirt-III PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-III daughterboard and MPX4250 MAP Sensor for building a MegaSquirt-III PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for c...
Add to cart -
MegaSquirt-III Daughterboard Kit
$230.00Upgrading your MS1 or MS2 to the latest MS3 has never been easier with this processor replacement! We've packaged the MS3 daughter board with 2 of the 40 pin sockets, so it will match up with our cases (required for upgrade) which have cutouts for the SD ...
Add to cart -
MegaSquirt-III MS3X Expansion Card & Connector Kit
$110.49Put this small circuit board in your MegaSquirt-III to unlock its full potential! This board installs in the MS3 case with no soldering; just connect it with the included ribbon cables. Install the MS3X board to add this whole list of inputs and outputs t...
Add to cart -
PKIT – GPIO Board Partial Kit
$178.00This is a very basic and incomplete starting point for building a GPIO (General Purpose Input/ Output) kit. It includes the main board, all SMD components soldered on, AMPSeal connector, and all the AMPSEAL pins, each crimped to a short length of TXL wire...
Add to cart -
CPU – MegaSquirt-II Daughterboard
$136.00MegaSquirt-II Daughterboard For upgrading your Megasquirt-I ECU, or replacement of your damaged MegaSquirt-II daughterboard. MS2 daughter cards are for use only with genuine Bowling & Grippo MegaSquirt mainboard PCBs. This is the latest version o...
Add to cart -
PKIT – MegaSquirt-I PCBv3.0 Partial Kit
$132.00MegaSquirt-I PCBv3.0 Partial Kit PCBv3.0, MegaSquirt-I CPU and MPX4250 MAP Sensor for building a MegaSquirt-I PCB 3.0 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE . Click HERE for complete MegaSquirt-...
Read more -
PKIT – MegaSquirt-I PCBv2.2 Partial Kit
$115.00MegaSquirt-I PCBv2.2 Partial Kit PCBv2.2, MegaSquirt-I CPU and MPX4250 MAP Sensor for building a MegaSquirt-I PCB 2.2 ECU. Complete Bill of Materials (parts listing) and assembly instructions can be found HERE. Click HERE for complete MegaSquirt-I ...
Read more -
CPU – MegaSquirt-I CPU
$999.00MegaSquirt-I CPU; Motorola 68HC908 microprocessor loaded with standard B&G MegaSquirt-I firmware version 3.0. This part is discontinued - sorry, we've sold out the whole stock. For use with any MegaSquirt PCB version 1, 2.2, 3.0, 3.57...
Read more
