Showing all 12 results
-
MegaSquirt V3.0 PCB Components Kit
$142.99This MSx30-Guts kit includes all the capacitors, diodes, integrated circuits, resistors, transistors, ECU connectors, the tube of heatsink compound and a bit of jumper wire in a Megasquirt V3.0 kit. The kit does not include the V3.0 PCB, case, endplates, ...
Add to cart -
8′ MegaSquirt Wiring Harness (MS1/MS2/MS3 Ready)
$99.99MegaSquirt Wiring Harness - 8 Feet Long We've completely redesigned our wire harness to help you get your fuel injection installation right the first time with several new features to help make your installation as easy and reliable as possible: ...
Add to cart -
MegaSquirt-I Programmable EFI System PCB2.2 – Kit
$197.00*This product or components that make up this product have reached End of Life. The ECU is now discontinued - this page is for reference only. MegaSquirt-I with V2.2 Main Board MegaSquirt programmable EFI Engine Management System from Bowling and ...
Read more -
MegaSquirt-I Programmable EFI System PCB3.0 – Kit
$999.00Part # MS130-K; MegaSquirt-I Programmable EFI System with V3.0 main board - Unassembled Kit with Black Case Important Note: The BIP373 coil driver is sold separately and is only required for direct coil control. If you are using coils with internal or ...
Read more -
MegaSquirt Relay Board – Assembled Unit
$264.99MegaSquirt Relay Board - Assembled Unit - Part# MSRelay-C Though the Relay/Power Board is not required, it is a convenience and can reduce the chance of miswiring during the installation. The relay board provides a central place for all of the required...
Add to cart -
MegaSquirt Wiring Bundle – 8′ Long
$62.99MegaSquirt Wiring Bundle 8' TXL wire, color coded with labeling printed on the wire every 3 inches -- no paper tags here! IAC and Ignition wires are included for MS-I / MS-2 use (or MS-3 Primary Harness use) Shielded Ignition input wire Grea...
Add to cart -
JimStim v1.5 MegaSquirt Stimulator with Wheel Simulator – Unassembled
$80.99Use this board to test the MegaSquirt's inputs and outputs on the bench, before you install it on a car! The JimStim features a microcontroller which allows the simulation of up to 30 different toothed wheels, in addition to the standard distributor s...
Add to cart -
JimStim 1.5 MegaSquirt Stimulator with Wheel Simulator – Assembled
$119.99DIYAutoTune Part# JimStim-C JimStim is essentially an engine simulator, a microcontroller which allows the generates up to 30 different toothed wheel signals, in addition to the standard distributor signal. Test your RPM input on the Stim, or tell the ...
Add to cart -
MegaSquirt JimStim Stimulator Power Supply
$17.5012v DC Power Supply Plugs directly into your MegaSquirt JimStim Stimulator! Power supply supports 120 to 240 volt AC power.
Add to cart -
Jumper 10-Pack
$7.4910-pack of wire jumpers in 5 colors. These fit 0.1" headers and are used on the JimStim to make connections for testing additional circuitry. There are several other uses for them too.
Add to cart -
Zeal Engineering Daughterboard with Dual VR Conditioners
$43.99The Zeal Engineering Daughterboard was designed and developed by Ken Culver, one of the authors of the MS2/Extra and MS3 firmware. We're proud to now offer this daughter card in kit form. It was originally developed for the FC RX-7, but we have found it...
Add to cart -
MegaSquirt Tuning Cable (DB9 Straight Thru)
$6.00DB9 6' Male/Female Straight thru cable for tuning and testing your MegaSquirt ECU.
Add to cart