Cart

Quick Links

DIYPNP Upgrade: Sequential Injection Kit
DIYPNP Upgrade: Sequential Injection Kit
DIYPNP Upgrade: Sequential Injection Kit
DIYPNP Upgrade: Sequential Injection Kit
DIYPNP Upgrade: Sequential Injection Kit

DIYPNP Upgrade: Sequential Injection Kit

(3 questions)
5 out of 5 based on 1 customer rating
(1 customer review)

$43.99

-

Add to wishlist
SKU: DP_SEQMOD-K Category: Brand:

Description

Add two extra injector drivers to your DIYPNP with this new module and the latest MS2/Extra code! We’ve partnered with JBPerf to develop this tiny module with two extra injector drivers. Allows for fully sequential injection on a 4 cylinder engine, semi-sequential on a 6 or 8 cylinder. Installs with a 10 pin shrouded header, included with the kit.

Click HERE for full DIYPNP Sequential Module Installation and Configuration Documentation.

Note: This is not intended for regular MS2s or standard MicroSquirts, only DIYPNPs and other devices built around the MicroSquirt Module.

Customer reviews

Rated 5 out of 5 stars
1 review
5 stars 1 100 %
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

1 review for DIYPNP Upgrade: Sequential Injection Kit

Only logged in customers who have purchased this product may write a review.

DIYPNP sequential injection mod kit on a V1.5 board

DIYPNP sequential injection mod kit on a V1.1 board

Can this be used with a regular MS2 or MicroSquirt?

  • It is only intended for use with MicroSquirt Module based devices like the DIYPNP.

Questions & Answers

    The IAC pin and 12v pin will function through the board???
  1. 0 votes
    Q The IAC pin and 12v pin will function through the board???
    Asked by luis baez
    A

    Yes, it does not interfere with these connections.
    2. Can the adapter board run low impedance injectors?
  2. 0 votes
    Q Can the adapter board run low impedance injectors?
    Asked by Mark
    A

    These drivers are intended for saturated (high impedance) injectors. Running low impedance injectors using this board without current limiting resistors may send the drivers into overcurrent protection or overheat the injectors.
    3. how to wire it up on microsquirt module? since i'm build an ECU without MSPNP package
  3. 0 votes
    Q how to wire it up on microsquirt module? since i'm build an ECU without MSPNP package
    Asked by Nandosuke
    A

    The pinout follows the above picture of the DIYPNP. The points you will need to connect are the two ground holes (green) to power ground, and connect PT6 and PT7 to the holes marked in red.
Only registered users are eligible to enter questions

Related products

  • Jumper 10-Pack

    Jumper 10-Pack

    5 out of 5
    $7.49

    10-pack of wire jumpers in 5 colors. These fit 0.1" headers and are used on the JimStim to make connections for testing additional circuitry.   There are several other uses for them too.

    Add to cart
  • MegaSquirt Relay Board - Assembled Unit

    MegaSquirt Relay Board – Assembled Unit

    5 out of 5
    $264.99

    MegaSquirt Relay Board - Assembled Unit - Part# MSRelay-C Though the Relay/Power Board is not required, it is a convenience and can reduce the chance of miswiring during the installation. The relay board provides a central place for all of the required...

    Add to cart

  • CPU – MegaSquirt-II Daughterboard

    4.5714285714286 out of 5
    $136.00

    MegaSquirt-II Daughterboard For upgrading your Megasquirt-I ECU, or replacement of your damaged MegaSquirt-II daughterboard.  MS2 daughter cards are for use only with genuine Bowling & Grippo MegaSquirt mainboard PCBs. This is the latest version o...

    Add to cart
  • MegaSquirt Wiring Bundle - Long

    MegaSquirt Wiring Bundle – 8′ Long

    4.2727272727273 out of 5
    $62.99

    MegaSquirt Wiring Bundle 8' TXL wire, color coded with labeling printed on the wire every 3 inches -- no paper tags here! IAC and Ignition wires are included for MS-I / MS-2 use (or MS-3 Primary Harness use) Shielded Ignition input wire Grea...

    Add to cart

  • DB37 Solder Cup Connector

     $3.00

    DB37 female solder cup connector, as included in our Megasquirt and relay board kits. Use this if you're making a new harness and prefer a soldered connection. This is the connector only; the backshell is sold separately.

    Add to cart
  • MegaSquirt 2 Kit with MapDaddy 4-bar map sensor upgrade

    MS230-K Kit with MapDaddy4 Upgrade

     $424.99

    Note:   Now using a brushed silver finish MS3 enclosure, which will help facilitate potential future upgrades from MS2 to MS3 without extra cost!  MegaSquirt-II Engine Management System with 3.0 Main Board - UnAssembled Kit; Part # MS230-K_m4 Th...

    Add to cart